Nanostructured alumina coatings manufactured by air plasma spraying: Correlation of properties with the raw powder microstructure
| dc.contributor.author | Zois, D. | en |
| dc.contributor.author | Lekatou, A. | en |
| dc.contributor.author | Vardavoulias, M. | en |
| dc.contributor.author | Vazdirvanidis, A. | en |
| dc.date.accessioned | 2015-11-24T17:36:26Z | |
| dc.date.available | 2015-11-24T17:36:26Z | |
| dc.identifier.issn | 0925-8388 | - |
| dc.identifier.uri | https://olympias.lib.uoi.gr/jspui/handle/123456789/14246 | |
| dc.rights | Default Licence | - |
| dc.subject | nanostructured alumina | en |
| dc.subject | coating materials | en |
| dc.subject | sintering | en |
| dc.subject | x-ray diffraction | en |
| dc.subject | sem | en |
| dc.subject | nanophase materials | en |
| dc.subject | alpha-al2o3 powder | en |
| dc.subject | titania coatings | en |
| dc.subject | wear | en |
| dc.subject | behavior | en |
| dc.title | Nanostructured alumina coatings manufactured by air plasma spraying: Correlation of properties with the raw powder microstructure | en |
| heal.abstract | High energy ball milled nanostructured Al(2)O(3) ("N"). fused/crushed conventional Al(2)O(3) ("C") and sintered nanostructurecl Al(2)O(3) ("S") powders were air plasma sprayed on 304 stainless steel The nanostructured powder was composed of nanoparticle agglomerates, whereas the conventional powder consisted of solid granules The average crystal size of the powders was estimated by X-ray diffraction based methods (the Scheirer equation and the Williamson Hall plot) Deviations between the crystal sizes calculated by the two methods indicated high lattice strain induced by the nanopowder production technique. Sintering of the nanopowder did not cause any considerable grain growth, moreover, the strain was alleviated The melting degree of the powders, reflected by the gamma-Al(2)O(3) content of the coatings, depended on their porosities Coatings "N" presented the lowest melting degree due to the inherent porosity of the agglomerated nanoparticles composing powder "N". As a result, their microstructure was characterized by high porosity and extensive microcracking. The "S" coatings exhibited higher melting degree than that of the "N" coatings (similar to that of the "C" coatings), due to a tighter microstructure attained by sintering. At the same time, part of the initial nanostructure had been preserved during sintering and spraying The "S" coatings presented the highest adhesion because they combined a high melting degree with pockets of retained nanostructure, the latter could act as crack arresters Increasing the spray power led to an increase in the melting degree and, consequently, a decrease in the coating porosity and an increase in the porosity affected properties (adhesion and hardness) (C) 2009 Elsevier B V All rights resented. | en |
| heal.access | campus | - |
| heal.fullTextAvailability | TRUE | - |
| heal.identifier.primary | DOI 10.1016/j.jallcom.2009.10.055 | - |
| heal.identifier.secondary | <Go to ISI>://000278749900080 | - |
| heal.journalName | Journal of Alloys and Compounds | en |
| heal.journalType | peer reviewed | - |
| heal.language | en | - |
| heal.publicationDate | 2010 | - |
| heal.publisher | Elsevier | en |
| heal.recordProvider | Πανεπιστήμιο Ιωαννίνων. Σχολή Θετικών Επιστημών. Τμήμα Μηχανικών Επιστήμης Υλικών | el |
| heal.type | journalArticle | - |
| heal.type.el | Άρθρο Περιοδικού | el |
| heal.type.en | Journal article | en |
Αρχεία
Φάκελος/Πακέτο αδειών
1 - 1 of 1
Φόρτωση...
- Ονομα:
- license.txt
- Μέγεθος:
- 1.74 KB
- Μορφότυπο:
- Item-specific license agreed upon to submission
- Περιγραφή: